1 inch Solenoid Valve 12 V Coil in Pakistan

1 inch Solenoid Valve 12 V Coil in Pakistan

1 inch Solenoid Valve 12 V Coil in Hallroad Pakistan

12V Solenoid Valve Coil 1 inch in Pakistan Featured here is Model 2W-250-25 of our brass valve line. This particular valve is a two-way, semi-direct lift valve with a normally closed operating position. This means that there are two ports in which media flows, the valve will open when the coil is energized and allow media to pass through. Removing the energy from the valve coil will close it and stop the flow. It works across various media such as hot water, air, gas, diesel fuel, Freon, weak acids and weak alkali. The valve features a heavy duty, solid brass body that’s sure to last in the most strenuous projects.

Features:

The port size is 1” inch female NPT threaded. This Electric Solenoid Valve can handle low viscosity fluids below 20 cst. The orifice size is 25mm and Cv value is 12. It can withstand pressure up to 115 psi (8 bar) and temperatures as low as 15°F and as high as 265°F. The seal material is FKM or Viton Rubber. This valve works in one direction and will not prevent media from moving backwards in the opposite direction. This specific valve has a 12 Volt DC coil with a voltage range that is -+ 10. The coil head is fitted with 5″ lead wires that can easily be connected with your own choice of terminals. The coils are not polarized, which mean that positive/negative does not matter when wiring them. The top of the coil features a label that indicates the valve type and specifications. Its response time is very low; in fact, it acts in less than one second, making it a great choice for all types of applications.

2,400

Confirm on WhatsApp before ordering

آڈر سے پہلے واٹس ایپ پر کنفرم کرلیں شکریہ۔

Description

1 inch Solenoid Valve 12 V Coil in Hallroad Lahore

Product Overview

The SZW-25-12VDC is a 12 Volt DC, 1” Stainless Steel, 2-way Solenoid Valve. This valve is compatible with a variety of media such as air, water, gas, diesel fuel, weak acids and glycol. The valve features a solid stainless steel body with a Viton seal. It is suitable for temperatures from 15°F up to 250°F. This valve requires 18 watts from a DC power source typical to that of a car battery.

This SZW-25-12VDC has no minimum pressure requirements and can operate up to 115PSI. This makes it ideal for gravity fed applications. The orifice size of the SZW-25-12VDC is 25mm allowing a higher flow rate when compared to other comparable solenoid valves.

The valve includes a 12 Volt DC coil that has a voltage tolerance of +-10%. This coil requires 18 watts or 1.5 amps to operate the valve. The coil has 5.5” lead wire connections for easy installation.

Installation: The coil has no polarity making power and ground interchangeable. There is an arrow indicating the direction of flow on the stainless valve body. Installed with the coil up is the preferred method however the valve will operate in any position. A pre-filter should be installed to prevent the valve from leaking caused by debris.

*Consult a chemical compatibility expert for correct seal and valve body material choice.

 

KUSZW-25-12VDC
PositionNormally Closed
Port Size1″ Female NPT
Voltage12V DC
Body MaterialStainless Steel
ComponentsStainless Steel
Seal MaterialViton® Diaphragm
Orifice Size25 mm
Temp Range15 to 250° F / -10 to 120°C
Pressure Range0 – 115 PSI (No Minimum Pressure)
Flow RateCv 12 (Appx 92 GPM @ 60 PSI)
Power18 Watts / 1.50 Amps
Coil ConnectionLead Wires
Response TimeFast Acting (Less than one second)

W1209 Temperature Controller in Hallroad Lahore

w1209 temperature controller

w1209 temperature controller

Sponsor

Sponsor 2