KY-040 Rotary Encoder Sensor Module Brick Sensor In Paksitan
KY-040 Rotary Encoder Sensor Module Brick Sensor | Microsolution Lahore
[happyforms id=”5763″ /]
₨130
CompareKY-040 Rotary Encoder Sensor Module Brick Sensor | Lahore
Specifications and Features :
- Model : KY-040.
- Type : Incremental Encoder.
- Cycles per revolution (CPR) : 20.
- Working voltage : 0 – 5V.
- Material : PCB + Brass.
- Weight : 10 gm.
- Size : 32 x 19 x 30 mm.
Related products
-
All MIcroSolution Pro, SENSORS
PIR INFRARED MOTION SENSOR AUTO ON OFF SWITCH MODULE in Pakistan
PIR INFRARED MOTION SENSOR AUTO ON OFF SWITCH MODULE AUTO LIGHTS LAMPS Hallroad Lahore
Attention
1. To turn off power when installation, must be installed by professional
2. This switch can work normally after 45 seconds when electricity, it is infrared Sensor preheat time
3. Do not overload to usePackage Included:
1 x IR Motion Sensor Light SwitchSKU: n/a -
All MIcroSolution Pro, SENSORS
Voltage Sensor Module DC 0-25V | Microsolution
Voltage Sensor For Arduino DC Raspberry Pi Amplifier Digital Current DC0-25V With Code.
Voltage Sensor Module DC 0-25V
The Voltage Sensor Module DC 0-25V is making this is because I couldn’t find any really helpful information on how to fix the code for my voltage sensor. Arduino’s have built in voltage sensors. Unfortunately, they only support voltages of 0-5 V. This module allows you to measure voltages of 0-25 V by presenting a lower voltage to the arduino for measuring.
After you have this value you simply feed it through some math and you get your actual voltage. Don’t ask me how this math works. I don’t know. If you do know however, please share. I’m really just editing the example code from the seller so that it will display decimal values instead far less useful int values.
By liking Our Facebook Page Embeded Studio , you can get special discount. Data Sheet of Voltage Sensor Module DC 0-25V can be also downloaded from the link.
To start you need to wire it up. It’s extremely easy as it only needs 3 wires.
Plug + into 5 V, – ground and S into an analogue pin. I have removed all but the relevant pins in a pin-out of the arduino nano. If you’re using another model then you’ll have to figure them out on your own. Any analogue pin will do. As far as I am aware at least. Once you have done this you’re ready to move on to the software.
- GND – This is where you connect the low side of the voltage you are measuring. Caution! : This is the same electrical point as your Arduino ground.
- VCC: The is where you connect the high side of the voltage you are measuring
- S: This connects to your Arduino analog input.
- – (or minus): This connects to your Arduino ground.
- +: This is not connected. It does absolutely nothing… zilch… nada… jack diddly doo doo.
[happyforms id=”5763″ /]
SKU: n/a -
All MIcroSolution Pro, SENSORS
WDD35D4 5K WDD35D-4 0 5K OHM 2W Condutive
WDD35D4 5K WDD35D-4 0 5K OHM 2W Condutive | Hallroad Lahore
Item specifics:
- Brand Name: AEYWVRL
- Condition: New
- Rated Power: 2W
- Resistance Tolerance: 0.5%
- Type: Conductive Plastic Potentiometer
- Model Number: WDD35D-4 5K
- is_customized: Yes
- Technology: Metal Alloy
- Resistance: 5K
SKU: n/a -
All MIcroSolution Pro, SENSORS
SGX (formerly E2V) MEMS gas sensor NO2 H2 O3 sensor MiCS-2714
SGX (original E2V) MEMS gas sensor NO2 H2 O3 sensor MiCS-2714
Brand SGX. Output model category Digital sensors Working principle Gas sensor Sensor category Energy consumption sensor Material Polymers 
[happyforms id=”5763″ /]
SKU: n/a
