SGX MEMS Air Quality Gas Sensor CO VOC NH3 in Pakistan
SGX MEMS Air Quality Gas Sensor CO VOC NH3 Nitrogen Compound MICS-6814 Hallroad Lahore
Item specifics:
- Brand Name: MILONT
- Sensitivity: check it
- Measuring Range: check it
- Type: Non Heating Type
- Linear: check it
- Resolution: check it
- Hysteresis: check it
- Sensor Type: Piezoelectric
- Repeatability: check it
- Output model category: Digital sensor
- working principle: Gas sensor
- Sensor class: Energy consumption sensor
- Material: polymer
₨4,500
CompareRelated products
-
SENSORS
SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A in Pakistan
0 out of 5(0)SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A in Hallroad Lahore Pakistan
This is SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A. SCT-013-000 is a Non-Invasive AC current sensor i.e. it is a current transformer that can be used to measure AC current up to 100 amperes.
This non-invasive current sensor clamped around the supply line can measure a load up to 30 Amps, and allow you to calculate how much current pass through it. It can be useful for building your own energy monitor or for building an over-current protection device for an AC load. This current clamp can be used to detect a current of up to 30A. Simply clip it around the current source that you wish to measure and it will produce a (very) small AC voltage proportional to the current. The cable is terminated on one end with a standard 3.5mm jack (like a headphone jack).
Use this to build your own energy monitor and keep your power usage down, or use it to build an over-current protection device for an AC load. See the link below for an example project. Check out the datasheet for the pinout of the 3.5mm jack.
Applications
- Suitable for the current measuring.
- Monitoring and protection of AC motor
- Lighting equipment
- Air compressor
Features :
- Non-invasive current transformer
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
- Two forms of output current, voltage (voltage output built-in the sampling resistor)
- Non-linearity ±3%(10%-120% rated input current)
- Output Plug 3.5mm.
Package Includes :
1 x 30A AC Current Sensor Module.
SKU: n/a -
All MIcroSolution Pro, SENSORS
Voltage Sensor Module DC 0-25V | Microsolution
0 out of 5(0)Voltage Sensor For Arduino DC Raspberry Pi Amplifier Digital Current DC0-25V With Code.
Voltage Sensor Module DC 0-25V
The Voltage Sensor Module DC 0-25V is making this is because I couldn’t find any really helpful information on how to fix the code for my voltage sensor. Arduino’s have built in voltage sensors. Unfortunately, they only support voltages of 0-5 V. This module allows you to measure voltages of 0-25 V by presenting a lower voltage to the arduino for measuring.
After you have this value you simply feed it through some math and you get your actual voltage. Don’t ask me how this math works. I don’t know. If you do know however, please share. I’m really just editing the example code from the seller so that it will display decimal values instead far less useful int values.
By liking Our Facebook Page Embeded Studio , you can get special discount. Data Sheet of Voltage Sensor Module DC 0-25V can be also downloaded from the link.
To start you need to wire it up. It’s extremely easy as it only needs 3 wires.
Plug + into 5 V, – ground and S into an analogue pin. I have removed all but the relevant pins in a pin-out of the arduino nano. If you’re using another model then you’ll have to figure them out on your own. Any analogue pin will do. As far as I am aware at least. Once you have done this you’re ready to move on to the software.
- GND – This is where you connect the low side of the voltage you are measuring. Caution! : This is the same electrical point as your Arduino ground.
- VCC: The is where you connect the high side of the voltage you are measuring
- S: This connects to your Arduino analog input.
- – (or minus): This connects to your Arduino ground.
- +: This is not connected. It does absolutely nothing… zilch… nada… jack diddly doo doo.
[happyforms id=”5763″ /]
SKU: n/a -
All MIcroSolution Pro, SENSORS
DHT11 DIGITAL TEMPERATURE AND HUMIDITY SENSOR in Pakistan
0 out of 5(0)DHT11 – Humidity and Temperature Sensor in Microsolution Hallroad Lahore
Specifications:
- Item: DHT11
- Measurement Range: 20-90%RH 0-50 ℃
- Humidity Accuracy: ±5%RH
- Temperature Accuracy: ±2℃
- Resolution: 1 Package:
- 4 Pin Single Row
- Pinning:
- 1=Vcc
- 2=Data
- 3=Open
- 4=GN
SKU: 50 -
All MIcroSolution Pro, SENSORS
Soil Moisture Meter for arduino in Pakistan
0 out of 5(0)Soil Moisture Meter for arduino Hallroad Lahore
Specification:
- Operating voltage: 3.3V~5V
- Dual output mode,analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Interface Description(4-wire):
- VCC: 3.3V-5V
- GND: GND
- DO: digital output interface(0 and 1)
- AO: analog output interface
SKU: n/a